Heating Repair Tips

Share Button

Before you call the hvac repair professional, here are suggestions to keep your furnace operating great this winter season. Here are some heater tips to understand and maintain your heating system. Here you will discover how check your furnace, how to turn it on and what to do if it won’t light.
Here’s how to turn on your heater:.
Check the breaker that regulates your heater. Turn it on.
Look for the heater switch. Usually it’s near the furnace. Turn it on.
Set your thermostat, switch the heater to heat, turn up the temperature and the heater ought to be going!
How to change your heater filter.
The furnace filter takes the dust out of the air that your heater is moving. After a while, it’s gathered as much dust as it can without slowing up the airflow in your air system. That’s the time to change the filter. Change it yearly, in the fall, or more often, as needed. Filters are cheap and only take a few minutes to swap out.
Open the furnace or filter door, Sometimes you have to look around a little to find it. It will be in the ductwork that returns air to your furnace.
Slide the old filter out. You can see if it needs replacing if you see it covered with dust. You ought to be able to see through the filter. If you can’t, change it. Actually, filters are cheap enough, change it anyway.
Slide in the fresh filter. Write the date on the visible edge of the filter.
Shut the door.
How to test your Heater’s airflow.
Do you have a cold room in your house? Possibly you are wondering if the heater is pumping air at all? Here’s an easy way to check.
Shut down your furnace at the thermostat. Take a common sized plastic garbage bag and tape it around a heat register. Turn on the furnace. Time how many seconds it takes to fill up the sack.
Seconds: 2 = 75 CFM (cubic feet/minute).
Seconds: 4 = 40 CFM.
Seconds: 10 = 20 CFM.
If your system is pumping under 10 CFM, then you should get the system checked out. (See below).
What to do if your central heater won’t ignite.
OK, the house is cold, no air is being pumped. The furnace is quiet. You hate to call the service man and have it be something you could have repaired yourself. What to do?
Check out the furnace switch, Is it on?
Is the thermostat set accurately? Is it switched to heat? Is the temperature level set high enough?
If the thermostat has batteries, are they fresh?
Is the venting for the heating system blocked by snow or ice? (See below).
Is the circuit breaker in the breaker box switched on?
Is the heater door correctly closed?
Do you have to change the furnace filter?
If none of the above are the trouble, call your furnace repair technician and they ought to be able to diagnose and fix the problem.
How to remove vent blockages.
If you think the heater vent is plugged with ice or snow, here’s what you should try.
Switch off the heater at the heater switch or at the breaker box. Them go remove the obstruction, when done switch the furnace back on.
What to do if your heater isn’t blowing air?
If your heater isn’t moving air and you’ve checked all of these, you might have a burnt out fan motor. Call the service specialist and get them to take a look.
Do you smell gas?
Gas smells a bit like rotten eggs. It can blow up or it can asphyxiate you. If you smell gas, don’t flip any switches. Open your windows and go to a neighbors to call the gas company, and/or the fire department or your furnace repair professional, right away. Don’t stay in a home that is leaking gas.
The best ways to save cash on your heat bill!
If your heating system is outdated, think about changing it. New heaters are so much more efficient than old hardware, you will recover the cost of the furnace, eventually, in your gas savings.
Does your home leak air?
A major loss of heat is around doors and windows. Seal up the cracks to minimize your heat bill. A lot of gas companies have subsidized programs that will seal up your house for you. Otherwise do it yourself.  Before you call the hvac repair professional, here are suggestions to keep your furnace operating great this winter season. Here are some heater tips to understand and maintain your heating system. Here you will discover how check your furnace, how to turn it on and what to do if it won’t light.
Here’s how to turn on your heater:.
Check the breaker that regulates your heater. Turn it on.
Look for the heater switch. Usually it’s near the furnace. Turn it on.
Set your thermostat, switch the heater to heat, turn up the temperature and the heater ought to be going!
How to change your heater filter.
The furnace filter takes the dust out of the air that your heater is moving. After a while, it’s gathered as much dust as it can without slowing up the airflow in your air system. That’s the time to change the filter. Change it yearly, in the fall, or more often, as needed. Filters are cheap and only take a few minutes to swap out.
Open the furnace or filter door, Sometimes you have to look around a little to find it. It will be in the ductwork that returns air to your furnace.
Slide the old filter out. You can see if it needs replacing if you see it covered with dust. You ought to be able to see through the filter. If you can’t, change it. Actually, filters are cheap enough, change it anyway.
Slide in the fresh filter. Write the date on the visible edge of the filter.
Shut the door.
How to test your Heater’s airflow.
Do you have a cold room in your house? Possibly you are wondering if the heater is pumping air at all? Here’s an easy way to check.
Shut down your furnace at the thermostat. Take a common sized plastic garbage bag and tape it around a heat register. Turn on the furnace. Time how many seconds it takes to fill up the sack.
Seconds: 2 = 75 CFM (cubic feet/minute).
Seconds: 4 = 40 CFM.
Seconds: 10 = 20 CFM.
If your system is pumping under 10 CFM, then you should get the system checked out. (See below).
What to do if your central heater won’t ignite.
OK, the house is cold, no air is being pumped. The furnace is quiet. You hate to call the service man and have it be something you could have repaired yourself. What to do?
Check out the furnace switch, Is it on?
Is the thermostat set accurately? Is it switched to heat? Is the temperature level set high enough?
If the thermostat has batteries, are they fresh?
Is the venting for the heating system blocked by snow or ice? (See below).
Is the circuit breaker in the breaker box switched on?
Is the heater door correctly closed?
Do you have to change the furnace filter?
If none of the above are the trouble, call your furnace repair technician and they ought to be able to diagnose and fix the problem.
How to remove vent blockages.
If you think the heater vent is plugged with ice or snow, here’s what you should try.
Switch off the heater at the heater switch or at the breaker box. Them go remove the obstruction, when done switch the furnace back on.
What to do if your heater isn’t blowing air?
If your heater isn’t moving air and you’ve checked all of these, you might have a burnt out fan motor. Call the service specialist and get them to take a look.
Do you smell gas?
Gas smells a bit like rotten eggs. It can blow up or it can asphyxiate you. If you smell gas, don’t flip any switches. Open your windows and go to a neighbors to call the gas company, and/or the fire department or your furnace repair professional, right away. Don’t stay in a home that is leaking gas.
The best ways to save cash on your heat bill!
If your heating system is outdated, think about changing it. New heaters are so much more efficient than old hardware, you will recover the cost of the furnace, eventually, in your gas savings.
Does your home leak air?
A major loss of heat is around doors and windows. Seal up the cracks to minimize your heat bill. A lot of gas companies have subsidized programs that will seal up your house for you. Otherwise do it yourself.  http://airconditioningrepairtoledo.com/